A few tips for hail repair needs: The two techniques mentioned above will remove the majority of hail damage on your car, but a professional job at your local auto body shop is recommended for deep dents or badly damaged surfaces. The services tend to be cheap, fast and rarely require a new paint job. However, it is a good idea to compare prices and offered services at various body shops to see which package works best for your wallet and car’s situation.
In the first place let’s start with some car paint care tricks: For small dents on your car hood, a car dent repair kit may be a simple and inexpensive solution. You can easily find these kits at any local auto supply store and they are very user-friendly. Each kit often includes a knockdown tool, a glue gun and many stems for different sized dents. You may be surprised at the way the kit works and the professional result it makes. But we do recommend this kid for small dents only. For deep, large dents, it is better if you take your car to garage as the repair kit can not fix them and even cause more damage.
Wax Your Car: Yes, I think it is accepted knowledge that your car needs to be waxed on a regular basis. If you have just bought a new car from a dealership, you must realize that no new car comes with wax from the manufacturer or dealer. New car prep does not mean the dealership is going to wax your car either. So that new car paint of yours is like taking a new-born child out in the sun with no sunblock on their skin. You can review my selection of best car waxes in helping you choose a quality car wax. Just remember your car should be waxed every 4-6 months under “normal” conditions. If you live in extreme weather conditions and you plan on keeping your car for over 5 years, you might consider applying wax to that new car paint even more frequently.
Apply the dry ice as many times as you need to, but it should pop out eventually if the dent isn’t too deep. You can also try heating up the dent first, with something like a hair dryer (similar to the hairdryer and compressed air tip above), and then apply the dry ice to it. Suction is one way to get out a dent, but the problem is finding a dent puller with the right amount of power. Well, why not just create your own? All you need is a pot (or bucket), a vacuum cleaner and some tape and you can get that dent out of your car in no time.
Using the Right Wax. Since each type of paint reacts differently to wax and polish, you need to find out which paint was used on your car and purchase detailing products that suit the paint. Some products may act as abrasive agents and strip the car off its original shine. Discover additional details on Auto Repair Colorado Springs.
The first step to performing a dent repair without using paint involves assessing the dent itself and determining if a paintless dent repair is even possible. According to most experts, 80 to 90 percent of dents can be repaired using PDR techniques. However, there are a certain percentage of dents that are impossible to repair without following it up with a paint job. The following types of dents usually fall into this “non-PDR” category: Very deep dents – Even very large dents can be repaired using PDR if the dent is fairly shallow. However, if a dent of any size is pushed in too far, the metal can’t be bent back into place without damaging the paint and requiring repainting.
So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.