The cost of tuning your auto with chip tuning files will be influenced by various components. These incorporate things, for example, how old the auto is, whether it has a PC or not, regardless of whether it has a merchant and whether it is carbureted or infused, among different factors. Beneath you will discover normal expenses for full tune ups. It ought to be noted you can settle the cost of tuning your auto by buying an engine manual and doing a significant part of the work yourself.
The moment you have carried out the modification you should purge out existing data in your ECU’s memory. You should then feed in fresh data pertaining to the conditions that have come into existence post modification. The ECU has to operate on the newly acquired data as this new data reflects the true conditions post modification. You should be well versed with the vital art of resetting the ECU of your car. You have to let your ECU adapt itself to the new situation arising out of the modification. Allow your ECU to relearn and perform.
Chip tuning or remapping advices? Generally speaking any car will see a benefit but the larger gains are from turbocharged applications. In a NASP (Naturally Aspirated) engine power gains are around 10-20%, but in a turbo engine the power gains are typically around 40% for a petrol and 30% for a turbo diesel. Even a car getting a relatively low power gain from a remap will actually be more lively to drive. The peak power gain figure is only a very small part of the equation. The engines response under acceleration and its torque curve are the primary reasons for getting into chip tuning. See more details at Boitier Additionnel Chrysler.
Can I send in my control unit by normal mail? You can send us your control unit by normal mail, and we do the programming directly on your control unit. Please fill in our form to this end and send it to us together with your control unit. Individual tunings for which we have no appropriate data can be carried out only directly on the vehicle. In the case of major hardware conversions, please send us a request by e-mail in advance. How does the chip tuning get to my control unit? It always depends on the vehicle. For older vehicles, before the 2000 model year, the EPROM (memory chip with the engine software) usually must be removed for writing and soldered in again. In the case of vehicles as of the 2000 model year, the optimized software can usually be written onto the engine control unit (flashed) via the OBD interface in the vehicle. Very new vehicles with tuning protection are read out and written with a special method. The control unit is removed and read and written with state-of-the-art BDM and boot pin devices.
Manufacturers generally sell one vehicle that covers various markets, with different tax and emissions regulations; different climates with extremes of heat, cold, humidity; different fuel quantities; different operating altitudes, etc. A manufacturer has to take all of these factors into consideration and make substantial compromises in the vehicles operation. Sales and marketing also have a big affect on the way an engine is mapped. If you look the in manufacturer brochure at the engine specs, the torque graph will rise, then flatten out on a straight line, and then drop off. This obviously isn’t how an engine breathes, and it’s the request of sales and marketing to produce this flat lining of the torque.
OEM clutch – for VW 2.0TDi 103kW engine – is designed for 400Nm torque. VW Q02 six-speed gearbox is rated for max. 500Nm. Factory engine calibration data allow 320Nm @ 1800-2500rpm. Bad standard remap can easily go over 400Nm right from 1800rpm. What do you think happen to OEM dual-mass clutch? It reminds me few years ago…we replaced friend’s clutch after one bad ECU remap combined with bad driver mentioned earlier. All piston heads love motorsport…we all watched Walter Roehrl, Ari Vatanen, Stig Blomqvist, Juha Kankunnen, Colin McRae, Ayrton Senna or Schumi…did you also noticed they never used low revs, rarely used mid range revs and most of time spent in high revs where optimal power and torque is. One wonders why so many drivers try to push it hard in low revs and chiptuners support this stupidity. Power = Torque x RPM. More engine revs less torque you need. Why do you need 96HP@380Nm@1800rpm if you can have 170HP@3500rpm where is the optimal place to shift gears. Read more info at Chip de Potencia Mazda.