A few tips on welding equipment, MIG and TIG welders, plasma cutters. Welders with a higher power output can work with thicker metals, but higher voltage welders will require special power supply set ups—either generators or appropriate power outlets. A welder with lower voltage in the 100’s will not be able to handle heavy duty jobs, but it can be plugged in and operated from any outlet. Any welder with power over 200 cannot run off a typical power outlet and will naturally cost more to run. In addition, welders will either run an alternating current (AC) that reverses itself at regular intervals or a direct current (DC) that flows in one direction and does not reverse itself. DC offers a steady rate of energy that leads to hotter temperatures and deeper weld penetration. AC welders usually cost less than DC welders, but the available electrodes are far more limited for AC. In fact, DC welders are more costly but remain popular because their higher power offers a wider selection of electrodes and a number of working advantages such as: simple arc striking, better penetration, and improved control. Welders who expect to work on a wide variety of projects may want to consider an AC/DC combination welder.
Searching for Welding supplies? Welding Supplies Direct & Associate company TWS Direct Ltd is an online distributor of a wide range of welding supplies, welding equipment and welding machines. We supply Plasma Cutters, MIG, TIG, ARC Welding Machines and support consumables to the UK, Ireland and Europe.
In many shops, the operator has to go to a tool room or supply area for a new contact tip, coil of wire or other welding accessory. This takes valuable time away from the welding cell and slows down overall productivity. To improve the operating efficiency and minimize wasted time, companies should stock at least a limited supply of all necessary items near the welding station – this includes shielding gas, flux and wire. Another helpful productivity enhancing tip is to switch to larger spools of wire such as from 25 lb. spools to 44 or 60 lb. spools to even larger packages of 1,000 lb. reels or 1,000 lb. drums. A simple switch like this means less changeover time, which adds up over the weeks, months and years. Shops should also be on the lookout for shielding gas waste. A simple device called a surge turbine can be placed at the end of the gun to provide a digital readout of the gas surge and flow rate. If the surge rate is high, investing in a surge guard can reduce the pressure, eliminating gas surges and waste. Leaks in the gas delivery system can also create a potential loss of money. By looking at the amount of consumables purchased each year and then examining the total gas purchased, a company can determine if there is a significant loss. Welding manufacturers and distributors should be able to provide average utilization figures so that loss can be detected. If there is a loss suspected, one of the easiest ways to check for leaks is to shut off the gas delivery system over the weekend. Check the level on Friday evening and then again on Monday morning to determine if gas was used while the system was in shut down mode.
MIG Welding Increases Welding Speed: In addition to welding aluminum and other softer metals, MIG-welding works faster, provides cleaner welds, and handles many different types of metals. The downside is its complexity. MIG Welders need direct currents, a steady stream of inert gas, and precise control of their torches. The amount of heat generated from MIG welding provides the deep penetration required for a strong weld, while also melting the feed wire rapidly enough to maintain a higher welding speed than other techniques. Given the inert gas required for MIG welding, keep in mind that this technique cannot be conducted in windy areas. The Right Stick Electrode Increases Welding Speed: There are three kinds of electrodes used for stick welding: fast-fill, fill-freeze, and fast-follow. While each electrode has its advantages, the fast-fill electrodes melt quickly and allow welders to work faster.
How to pick a welder tips: Duty cycle: The advertised amperage of the machine offers a headline guide, but the duty cycle of the machine gives up the truth. Light industrial machine duty cycles can be as low as 20%, but more heavy duty MIG’s should range between 40-60%. If a 300amp MIG has 30% duty cycle for instance, it’s on the edge of acceptability. Duty cycle is determined by how many minutes out of 10, it can weld at 100%. Duty cycle testing: MIGS tested at 20 Degrees & 40 Degrees we consider good. (Beware any manufacturer who doesn’t quote an ambient temperature for testing) Manufacturer’s warranty: Always a great guide to quality. A three year warranty is good. Weld characteristics: Make sure the arc is smooth & suits your application. (Some machines are better suited at the low range and others at higher amperage range).
Business Name: Welding Supplies Direct & Associate company TWS Direct Ltd
Website: https://www.migwelders.ie/
Address : TWS Direct Ltd. Unit 1 M54 Space Centre.
Halesfield 8. Telford. Shropshire. TF7 4QN
Phone : +44 (0) 1952 582 260
Email: sales@weldingsuppliesdirect.co.uk
Office Hours: Mon – Frid / 9:00Am – 17:30pm